The top chamber has one hole, and the bottom two chambers each have two holes. The pressure will push the sludge and air bubbles out of the bottom. Now you’ll need to remove the air bubbles and sludge out of the bottom of the cartridge using one of the following methods: Method 1įor the black cartridge, you can seal the four holes and blow air into the remaining hole. The result might not look much different than the first attempt, but the solution should have helped soften the clog. Soak the cartridges in this solution overnight, and run another test print the next day. Add a quarter-inch of BCH’s Triple Action Cleaning Solution to the bowl of water. If the ink has failed to pass through to the paper, or the text is blurry, then it’s likely that dried ink and debris is still clogging the cartridge. Re-insert your cartridge in the printer and do a test run to see whether or not it works. This will loosen the dirt and make the cleaning solutions more effective. Then, put the clogged cartridge in the bowl for 10 minutes. First, fill a bowl with a quarter-inch of water and heat it in the microwave for one minute. Thankfully, there’s an easy way to fix this. You may run into additional problems when trying to refill or reinstall your ink cartridge, and these are often caused by a clogged printhead. You can either switch to BCH’s larger sponge, or make a spongeless cartridge with this kit. If you find that the cartridge empties too quickly, you may have a sponge problem.However, be aware that most starter cartridges-about 76%-are NOT refillable. HP makes more refillable cartridges for XL, as well as standard cartridges. If this happens, your cartridge is not refillable and you will have to try a different one. The printer will display an “E1” error.Remember to refill the cartridge before it empties. In that case, just keep using the printer and ignore the ink level on your computer. The printer may keep printing with the ink level at zero.You can simply keep printing until the ink level on your computer reaches zero. Post-Refill Ink LevelsĪs mentioned previously, your printer will not show the updated refilled ink level, instead displaying the old amount. If your printer still displays an error, that means the cartridge is damaged and needs to be replaced. If you receive an error message stating “the cartridge cannot be found” or “take the cartridge out,” then remove the cartridge, clean the contact ribbon, and re-insert it. Note that the printer will not track the ink level after being refilled, so you will need to keep an eye on it yourself. If the printer displays a “low ink” or “ink depleted” message, you can hit “ok” or “yes” to dismiss these warnings and keep printing. Allow the cartridge to sit in the printer overnight, and the bubbles should be gone the next day. If the cartridge does not print correctly, the refill process may have introduced air bubbles on the bottom of the cartridge. Reinstall the ink into the printer and run one or two cleaning cycles until the cartridge begins to print correctly. Step 5Ĭlean the top of the cartridge and place a piece of transparent scotch tape on the hole (optional). Stop if the ink starts to well up from the fill hole. Slowly inject the ink into the cartridge. Press down on the sponge and begin injecting your ink - about seven squeezes of the bottle should do it. Insert the needle into the correct refill hole until you feel the sponge, but don’t go too deep. XL cartridges take 2.5 ml of colored ink, and 7 ml of black. For regular-sized cartridges, use 1.5 ml of colored ink, or 4 ml of black ink. Note, however, that you cannot refill regular cartridges to XL capacity, as the two are configured differently inside. Step 2Īttach a needle to the syringe and load the syringe with the correct ink color. Carefully pierce these holes without removing the label, as this will make the refill process easier. These can be found by locating the rounded dent near the middle of the cartridge. Run a toothpick across the top of the cartridge on the manufacturer’s label to locate the refill holes. Black, cyan, magenta, and yellow ink (30 ml per bottle).We recommend using the First-Timer Ink Refill Kit for HP Inkjet Printer Cartridges: 60 61 62 63 64 65 66 67 EZ30-T, which can be purchased at for $17.99.
Hp printer how to use 64 cartridges instead of 62 how to#
This short guide will walk you through the process of how to refill HP 67 and 67 XL cartridges. Minimizing the number of plastic cartridges you buy is a climate-conscious choice that anyone can make. But you may ask, why bother? First and most obviously, it saves you money. Rather than going out to buy a new ink cartridge the moment you start to notice your current one running dry, you might consider a simple refill.